User Tools
accessories:beam-analyzer-c100
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
accessories:beam-analyzer-c100 [2024/04/30 15:16] Bob Varkevisser [Technical Specifications] |
accessories:beam-analyzer-c100 [2024/12/28 13:07] (current) Bob Varkevisser [Download and installation of the software] |
||
|---|---|---|---|
| Line 9: | Line 9: | ||
| ====== Technical Specifications ====== | ====== Technical Specifications ====== | ||
| - | Optical | + | === Optical |
| + | |< 100% 60% ^ 40% >| | ||
| ^ Parameter ^ Range ^ | ^ Parameter ^ Range ^ | ||
| | Optical power (*) (* *) | 0.1W - 100W | | | Optical power (*) (* *) | 0.1W - 100W | | ||
| - | | Accuracy on power measurement (Calibrated on RGB) | 1% | | + | | Accuracy on power measurement (Calibrated on 635nm / 520nm / 445nm). Other wavelengths can be added by the user | 1% | |
| | Resolution on divergence (by design) | 0.01 mrad | | | Resolution on divergence (by design) | 0.01 mrad | | ||
| | Typical accuracy (+/-) | 0.01 mrad | | | Typical accuracy (+/-) | 0.01 mrad | | ||
| Line 24: | Line 24: | ||
| (* *) A correct alignment should be done before setting the laser projector to maximum power. The user must follow the alignment procedure described in the User Manual to prevent damage to the system. | (* *) A correct alignment should be done before setting the laser projector to maximum power. The user must follow the alignment procedure described in the User Manual to prevent damage to the system. | ||
| - | Mechanical | + | === Mechanical |
| - | ^ Parameter ^ ^ | + | |< 100% 60% ^ 40% >| |
| + | ^ Parameter ^ Value ^ | ||
| | Length x Width x Height (mm) (Without holder) | 105 x 75 x 59 | | | Length x Width x Height (mm) (Without holder) | 105 x 75 x 59 | | ||
| | Length x Width x Height (mm) (With holder) | 153 x 110 x 70 | | | Length x Width x Height (mm) (With holder) | 153 x 110 x 70 | | ||
| - | | Weight | + | | Weight |
| - | | Weight | + | | Weight |
| - | + | ||
| - | Electrical Specifications: | + | |
| - | ^ Parameter ^ ^ | + | === Electrical === |
| + | |< 100% 60% ^ 40% >| | ||
| + | ^ Parameter ^ Value ^ | ||
| | Typical Power consumption (USB 3.0) | 2W | | | Typical Power consumption (USB 3.0) | 2W | | ||
| Line 43: | Line 44: | ||
| * USB 3.0 port | * USB 3.0 port | ||
| - | * Computer with Windows 10 or 11 installed | + | * Computer with Windows 10 or higher |
| ====== How to use the Beam Analyzer ====== | ====== How to use the Beam Analyzer ====== | ||
| Line 51: | Line 52: | ||
| To install the software, simply download and start the setup file “LBA_vX.XX_setup.exe” (X.XX is the version of the software). The latest version of the software can be found **[[https:// | To install the software, simply download and start the setup file “LBA_vX.XX_setup.exe” (X.XX is the version of the software). The latest version of the software can be found **[[https:// | ||
| + | [[https:// | ||
| ==== Shoot the laser beam on the beam analyzer ==== | ==== Shoot the laser beam on the beam analyzer ==== | ||
| Line 64: | Line 66: | ||
| {{accessories: | {{accessories: | ||
| - | The sensor should remain below 75°C at any time. | + | __**The sensor should remain below 75°C at any time.**__ |
| Create a beam pattern, with around 1000 points (~30FPS), or the maximum point number you can if 1000 is not possible, set it to low power and enable it. Incline slightly Left, right, Up, and down the LBA-C-100 in front of your laser until you see a part of the “9 spots pattern”. Keep shooting at the center of the lens. | Create a beam pattern, with around 1000 points (~30FPS), or the maximum point number you can if 1000 is not possible, set it to low power and enable it. Incline slightly Left, right, Up, and down the LBA-C-100 in front of your laser until you see a part of the “9 spots pattern”. Keep shooting at the center of the lens. | ||
accessories/beam-analyzer-c100.1714482976.txt · Last modified: 2024/04/30 15:16 by Bob Varkevisser
