User Tools
accessories:beam-analyzer-c100
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
accessories:beam-analyzer-c100 [2024/04/30 15:17] Bob Varkevisser [Requirements] |
accessories:beam-analyzer-c100 [2024/12/28 13:07] (current) Bob Varkevisser [Download and installation of the software] |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| === Optical === | === Optical === | ||
| + | |< 100% 60% ^ 40% >| | ||
| ^ Parameter ^ Range ^ | ^ Parameter ^ Range ^ | ||
| | Optical power (*) (* *) | 0.1W - 100W | | | Optical power (*) (* *) | 0.1W - 100W | | ||
| - | | Accuracy on power measurement (Calibrated on RGB) | 1% | | + | | Accuracy on power measurement (Calibrated on 635nm / 520nm / 445nm). Other wavelengths can be added by the user | 1% | |
| | Resolution on divergence (by design) | 0.01 mrad | | | Resolution on divergence (by design) | 0.01 mrad | | ||
| | Typical accuracy (+/-) | 0.01 mrad | | | Typical accuracy (+/-) | 0.01 mrad | | ||
| Line 24: | Line 25: | ||
| === Mechanical === | === Mechanical === | ||
| - | ^ Parameter ^ ^ | + | |< 100% 60% ^ 40% >| |
| + | ^ Parameter ^ Value ^ | ||
| | Length x Width x Height (mm) (Without holder) | 105 x 75 x 59 | | | Length x Width x Height (mm) (Without holder) | 105 x 75 x 59 | | ||
| | Length x Width x Height (mm) (With holder) | 153 x 110 x 70 | | | Length x Width x Height (mm) (With holder) | 153 x 110 x 70 | | ||
| - | | Weight | + | | Weight |
| - | | Weight | + | | Weight |
| === Electrical === | === Electrical === | ||
| - | ^ Parameter ^ ^ | + | |< 100% 60% ^ 40% >| |
| + | ^ Parameter ^ Value ^ | ||
| | Typical Power consumption (USB 3.0) | 2W | | | Typical Power consumption (USB 3.0) | 2W | | ||
| Line 49: | Line 52: | ||
| To install the software, simply download and start the setup file “LBA_vX.XX_setup.exe” (X.XX is the version of the software). The latest version of the software can be found **[[https:// | To install the software, simply download and start the setup file “LBA_vX.XX_setup.exe” (X.XX is the version of the software). The latest version of the software can be found **[[https:// | ||
| + | [[https:// | ||
| ==== Shoot the laser beam on the beam analyzer ==== | ==== Shoot the laser beam on the beam analyzer ==== | ||
| Line 62: | Line 66: | ||
| {{accessories: | {{accessories: | ||
| - | The sensor should remain below 75°C at any time. | + | __**The sensor should remain below 75°C at any time.**__ |
| Create a beam pattern, with around 1000 points (~30FPS), or the maximum point number you can if 1000 is not possible, set it to low power and enable it. Incline slightly Left, right, Up, and down the LBA-C-100 in front of your laser until you see a part of the “9 spots pattern”. Keep shooting at the center of the lens. | Create a beam pattern, with around 1000 points (~30FPS), or the maximum point number you can if 1000 is not possible, set it to low power and enable it. Incline slightly Left, right, Up, and down the LBA-C-100 in front of your laser until you see a part of the “9 spots pattern”. Keep shooting at the center of the lens. | ||
accessories/beam-analyzer-c100.1714483059.txt · Last modified: 2024/04/30 15:17 by Bob Varkevisser
