Fulltext results:
- FB4 Settings Basics
- one important detail: The FB4 hardware may be the controller even if it is in another mode, or connected to an... ize this situation, imagine a network with 60 FB4 controllers. BEYOND allows the connection of not more than 4... do some other adjustments of all or any of the 60 controllers. We can do this with a connection less model. An... a software, but it is not the only purpose of the controller. It is one of reasons why the FB4's are separate
- BEYOND Laser and EmuLaser control hardware
- rop down list) displays a list of connected laser controller hardware units, virtual controllers (demo), and EmuLasers (designates a video projector controlled by your vi... main purpose of this menu is set the order of the controllers as well as manage Demo and EmuLaser units. {{:b... ct to the hardware, click “Refresh list and reset controllers” button. This button is for FB3 hardware control
- BEYOND MIDI settings
- it by moving a slider or pressing a button on the controller. If it is connected correctly, you should see a M... s this appear in recent builds of BEYOND”? MIDI controllers have many buttons, sliders, knobs, etc... But ev... ws/dialogs, work for FX too. To configure a MIDI controller to be able to activate the main cue grid of a BEY... , and for the secondary grid, you can use a MIDI controller like the Livid OHM.** Double click on a cell to
- The Configuration Dialog Box
- , Tuning, Grid, Timecode In, Timecode Out, Video, Controllers, Blackout, Zone Hotkeys, Laser Preview, and Log ... the magnifying glass in the bottom left.// ===== Controllers Tab ===== {{:beyond:configuration_window_01_controllers.jpg?600|}} This setting will enable or disable the... INT: You can enable or disable the start of QM000 controllers, during the startup of BEYOND. Right after BEYON
- BEYOND DMX Settings
- rter. Currently BEYOND supports the __DMX USB PRO controller from the company ENTTEC__. This is a very popular... ct FB3-SE control and playback from a DMX console controller or application.// {{:beyond:dmxsettings1.png?no... means of ArtNet protocol, the Enttec DMX PRO USB controller or Pangolin QM2000 hardware. To setup the communi... urce. **Details for communication with the Enttec controller are located on other tab called ENTTEC**. To use
- Vectors and Points
- mes. The software sends the Frame to the hardware controller to transform the digital Frame to an analog waveform. The output from the controller is an analog signal. The same situation as in the... of speakers. In laser display – we have Frames, a controller for making the analog signal, a scanner amp, and ... as equal duration, but a different value. A laser controller uses the Samples as the input of the DAC (Digital
- Firmware Updater
- e version when it opens or an additional hardware controller is connected to the system (while BEYOND is open)... BEYOND detects incorrect firmware is loaded on a controller, BEYOND will update it. Otherwise, the controller cannot be used within BEYOND. During a firmware update, BE... ts of desktops. **Problem with computer USB Host controller** - Very unexpected issue, but sometimes the con
- Projector Settings Menus
- e use of Pangolin hardware such as a QM2000 or FB controller. BEYOND uses a hardware serial number for the ide... r settings. Positioning of a projector’s hardware controller in the list is not important, because BEYOND uses... rs** in the list then use the “Laser and EmuLaser controllers” menu. The Order of projectors is important fo... ick and easily ordering of the connected hardware controllers. ===== Toolbar ===== ^Tool^Description^ |Open
- Laser and EmuLaser Control Hardware
- low indicates where you can view all the Hardware Controllers connected to your computer that are visible with... he calculation core, allowing you to position the controllers in the right order. When this is done, controllers will appear as Projectors. {{:beyond:beyondemulaser1.png... nolink|}} When you click “Refresh List and reset Controllers”, this will disconnect, and then attempt to reco
- TimeCode and BEYOND
- ick on the Main “Settings” menu and select ”SMPTE Controller Settings”. - Click on “Enable controller communication” to create a corresponding communication component ... lect a communication port that corresponds to the controller you are using. - Select the time format and en... t button to start communication with the TimeCode controller which will perform a test connection. At the end
- Networking for Lasershows, BEYOND, and Entertainment
- sses for “private” networks. With this schedule, controllers could be configured to be something like - L... er. Over the next couple milliseconds every laser controller in the rig receives their frame, and waits for th... output and things like distributed scanning. The controllers just get a heartbeat signal that keeps all their... t out of BEYOND, but doesn’t make it to the laser controllers before the “display time” they are expecting the
- Projection Zones in BEYOND
- a listing is red, it is because there is no laser controller that is able to output to that projector (scanner... to**” allows you to indicate the projector (Laser Controller Serial number) that will be used for that zone, a... of settings is as follows: - Set the order of controllers in the Laser and EmuLaser hardware dialog - A... ojector Settings - Adjust the Projection Zones Controllers and Projectors are sort of “low-level layer” tha
- Using a Gamepad in BEYOND
- ed settings within the Control Panel. The Gamepad controller may require calibration and it is important to se... BEYOND, the settings are very simple. Select the controller inside the Controller list, BEYOND will show information about the controller, and allow testing of the device. ===== Gamepad and
- BEYOND Security Guide
- to choose a serial number from list of connected controllers. * Clicking on “Password” will call up a dialo... ized Users You need to know the serial number of controller that will be used by the authorized user, or deci... uld confirm that you are the Author/creator. Your controller must be connected or password registered in the s
- FB4 Browser
- ders contained on the FB4 SD card, of the current controller. Standard files have predefined icons. Other file... Network bandwidth may be shared between multiple controllers and protocols, so it might influence the data tr... **Reboot FB** – restart/reboot the current FB4 controller. ===== Status Panel ===== The Status Panel ind