User Tools
hardware:fb4:dmx39
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
hardware:fb4:dmx39 [2019/08/20 11:20] Bob Varkevisser |
hardware:fb4:dmx39 [2022/12/12 11:50] (current) Bob Varkevisser |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== FB4 39 Channel DMX Profile layout ====== | ||
| + | |||
| + | **Note that this profile is active when the FB4 is in operation mode **DMX-512** or **ArtNET** and in menu "DMX settings", | ||
| + | |||
| + | |||
| + | The 39-channel fixture mode is meant to be used as follow; | ||
| + | - Place the FB4 in “Setup mode”. (Note that there is a two second delay before “setup mode” will initialize). Now limit the area where the laser may project. | ||
| + | - Place the FB4 in “playback mode”.\\ Do the actual show performance and have the ability to use shape generators. | ||
| + | |||
| + | <WRAP center round important> | ||
| + | During “Setup mode”, channels 14 till 39 will ignore DMX/Art-net changes.\\ | ||
| + | During “playback mode”, channels 2 till 13 will ignore DMX/Art-net changes. | ||
| + | </ | ||
| + | |||
| + | |||
| + | ^Channels^Value^Function^Description^Width^ | ||
| + | |1 ((Set Channel one at least 2 seconds on DMX value 240 to activate setup mode. Channel 2 till 12 can only be modified when channel one is in setup mode During setup the red light on the FB4 will blink. | ||
| + | During playback mode, the red light will burn continuously.))|0-255|Fixture Modes|0-239 Blackout / Safe\\ 240-240 Setup Mode\\ 251-251 Playback mode|8 Bit| | ||
| + | |2|0-255|Max Intensity|Defines the max intensity that can be used during playback mode\\ (Range 0 till 100)|8 Bit| | ||
| + | |3|0-255|Test frames|Allows enabling test frames during setup mode\\(1= test frame 1, 255 = test frame 255)|8 Bit| | ||
| + | |4, | ||
| + | |6, | ||
| + | |8, | ||
| + | |10, | ||
| + | |12, | ||
| + | |14|0-255|Pages|Page Index, 255 pages in total\\ 1 = page 1, 255 = page 255|8 Bit| | ||
| + | |15|0-255|Cues|Cue Index, 255 Cues in total\\ (1 = cue 1, 255 = cue 255)|8 Bit| | ||
| + | |16 ((If a BPM based effects is exported at 100BPM, and you want to have a cue running on 128 BPM, change the speed to 128.))|0-255|Cue Speed|(0 = Original, 1 – 255 = 1% till 255%)|8 Bit| | ||
| + | |17|0-255|Dimmer|Defines the maximum brightness limited by setup mode\\ (Range 0 till 100%)|8 Bit| | ||
| + | |18, | ||
| + | |20, | ||
| + | |22, | ||
| + | |24, | ||
| + | |26, | ||
| + | |28, | ||
| + | |30, | ||
| + | |32 ((Lowering the scan rate can impact the cue speed of the laser))|0-255|Scan Rate|Defines the painting speed of the laser beam.\\ (5k till original 30K)|8 Bit| | ||
| + | |33|0-255|Red|Intensity range from 0 till 100%|8 Bit| | ||
| + | |34|0-255|Green|Intensity range from 0 till 100%|8 Bit| | ||
| + | |35|0-255|Blue|Intensity range from 0 till 100%|8 Bit| | ||
| + | |36|0-255|Alpha|Allows you to shift between original cue color or RGB control.\\ (Range, 0 = original, 1-255 = 0 till 100% alpha blending)|8 Bit| | ||
| + | |37|0-255|Points start|Allows you to remove points from the start point of a cue\\ (Range from 100 till 0% visibility)|8 Bit| | ||
| + | |38|0-255|Points End|Allows you to remove points from the end point of a cue\\ (Range from 1000 till 0% visibility)|8 Bit| | ||
| + | |39|0-255|Strobe|0 = Strobe disabled\\ 1-255 = Strobe from 1 to 20 Hz|8 Bit| | ||
| + | |||
| + | ===== Cheat Sheet ===== | ||
| + | |||
| + | {{ : | ||
Page Tools
