User Tools
safety:safetyscan_lens
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
safety:safetyscan_lens [2021/04/19 11:12] Bob Varkevisser [SafetyScan lens discussed by laserists] |
safety:safetyscan_lens [2022/07/18 15:39] (current) Bob Varkevisser [Lens mount designed by Kvant] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== SafetyScan Lens and Kvant lens mount ====== | ====== SafetyScan Lens and Kvant lens mount ====== | ||
| - | |||
| - | {{: | ||
| ===== Introduction and purpose for using a lens ===== | ===== Introduction and purpose for using a lens ===== | ||
| Line 14: | Line 12: | ||
| In addition to the information provided below, Pangolin has also produced a 15-minute video showing how to mount the lens, how to perform safety measurements, | In addition to the information provided below, Pangolin has also produced a 15-minute video showing how to mount the lens, how to perform safety measurements, | ||
| + | |||
| + | < | ||
| + | <iframe width=" | ||
| + | </ | ||
| ===== Selecting the proper lens ===== | ===== Selecting the proper lens ===== | ||
| Line 164: | Line 166: | ||
| The third degree of adjustment is tilting the lens about the split at the top. If the top portion of the lens is at an angle with respect to the light coming from the X-Y scanners, there will be a kind of “ghost image”, which is a reflection off of the top surface of the lens. The lens angle should be adjusted so that the beams for the center of the projection are directly in angular alignment with respect to the top surface of the lens. Doing so will prevent the “ghost image” and the result will be perfect. The crude picture below shows the concept. | The third degree of adjustment is tilting the lens about the split at the top. If the top portion of the lens is at an angle with respect to the light coming from the X-Y scanners, there will be a kind of “ghost image”, which is a reflection off of the top surface of the lens. The lens angle should be adjusted so that the beams for the center of the projection are directly in angular alignment with respect to the top surface of the lens. Doing so will prevent the “ghost image” and the result will be perfect. The crude picture below shows the concept. | ||
| - | {{: | + | {{: |
| As mentioned above, we produced a video which explains all three degrees of lens adjustment (starting around time 11:20) here: [[http:// | As mentioned above, we produced a video which explains all three degrees of lens adjustment (starting around time 11:20) here: [[http:// | ||
| Line 172: | Line 175: | ||
| Kvant manufactures a lens mount that can be used to attach a SafetyScan lens to their laser projectors. A rendering of an example projector that uses a lens mount and SafetyScan lens is shown below. | Kvant manufactures a lens mount that can be used to attach a SafetyScan lens to their laser projectors. A rendering of an example projector that uses a lens mount and SafetyScan lens is shown below. | ||
| - | {{: | + | {{: |
| To use the SafetyScan Lens and **lens mount**, do the following: | To use the SafetyScan Lens and **lens mount**, do the following: | ||
| Line 185: | Line 188: | ||
| ===== Lens Engineering Drawing ===== | ===== Lens Engineering Drawing ===== | ||
| - | {{: | + | {{: |
| //Due to our policy of continuous product improvement, | //Due to our policy of continuous product improvement, | ||
| Line 197: | Line 200: | ||
| The manufacture, | The manufacture, | ||
| - | |||
| - | ===== Instruction Videos ===== | ||
| - | |||
| - | ==== How To Install The SafetyScan ™ Lens ==== | ||
| - | |||
| - | < | ||
| - | <iframe width=" | ||
| - | </ | ||
| - | |||
| - | ==== SafetyScan ™ lens discussed by laserists ==== | ||
| - | < | ||
| - | <iframe width=" | ||
| - | </ | ||
| - | |||
| - | ==== Theory, Installation and Use ==== | ||
| - | < | ||
| - | <iframe width=" | ||
| ===== License Agreement and Limited Warranty ===== | ===== License Agreement and Limited Warranty ===== | ||
safety/safetyscan_lens.1618823530.txt · Last modified: 2021/04/19 11:12 by Bob Varkevisser
