Fulltext results:
- Tips: Scan speeds and LC4D
- when the ILDA Test Pattern is displayed at 30,000 points per second: | {{:tools:lc4d:sslc4d1.jpeg?nolink|... Now, some people may adopt a scan speed of 30,000 points per second. In fact, this is Pangolin's suggestio... ere are two cases: You tune and project at 30,000 points per second, or you prefer other speeds for tuning... n Lasershow Converter MAX. This is usually 30,000 points per second. Lasershow Converter MAX's default se
- Post-Render Effect: Laser Output, Preview Options and Save Functions
- ponds with frame 2 in BEYOND, etc. ===== Minimum Points ===== This sets the minimum number of laser points rendered in each frame. This could be handy for keep... frame rate consistent. For example, if **Minimum points** was set to 1000 points, you would always get a maximum of 30 frames per second if the sample rate (poin
- Tips: Point spacing for objects
- default point spacing settings have the **Corner points 165-170°** value set to zero. But this might make... positions. Therefore, it is best to set **Corner points 165-170°** to the same number as sharper (larger)... a round outline. One way is to set the **Corner points** at various angles to a value of 0. {{:tools:lc... urve Detect ===== Once you have prevented corner points from being placed on the sphere outline (either b
- Questions and answers
- I be worried about the laser image having so many points it flickers? ===== Flicker should not be a signi... bjects, Lasershow Converter 4D may render lots of points. But in all of the scenes that Pangolin has seen ... mselves out so that there really aren't that many points. ===== Can I undo my work? ===== Yes! The **Und
- Tips: Point spacing for lines
- results in laser frames with the least number of points. {{:tools:lc4d:point-spacing-for-lines-1.gif?nol... t value of 300. This ensures there will be enough points placed for small details and to avoid rounding in... lines ===== The default setting for **AutoAnchor Points** (shown below) has **Accelerate/Decelerate** ena... n and out of lines. It also reduces the number of points that you need to use at the beginning and ending
- Tips: Color and path consistency
- ut it could be that a better beam path with fewer points could be derived if you had set a different selec... jump around unnecessarily, or that extra blanking points were included during the drawing of the intersect
- Object Tag: Soft Line
- **Soft Line at line beginning** is the number of points over which fading will occur at the beginning of ... e. **Soft Line at line ending** is the number of points over which fading will occur at the ending of a l... **Soft Line at round overlaps** is the number of points over which fading will occur at both the beginnin... cles. **Soft Line at corners**, is the number of points over which fading will occur at the ending of a l
- Object Tag: Point Spacing
- d, when running at a point output speed of 30,000 points per second. If you do not change any of the numbe... C 4D]]. ===== About point spacing ===== The way points are placed in lines depends on whether the object... square, lines will always start with **AutoBlank Points at line endings**, followed by **AutoAnchor Points**. * If the object is round, a special point placeme
- Object Tag: Line Types
- the object, but does not actually write any data (points) to the laser frame. This lets the object mask or... eeing other objects) and keep them from producing points. ===== See Also ===== * [[tools:lc4d:tip_cont
- Object Tag: Filter Settings
- 3.0, Lasershow Converter 4D will not generate any points on the laser display if a line is less than 3.0 p
- Post-Render Effect: Laser Output, Preview Options and Save Functions
- ponds with frame 2 in BEYOND, etc. ===== Minimum Points ===== This sets the minimum number of laser points rendered in each frame. This could be handy for keepi... frame rate consistent. For example, if **Minimum points** was set to 1000 points, you would always get a maximum of 30 frames per second if the sample rate (poin
- What's new
- s. The additional information shows the number of points in the frame, as well as the Z-axis coordinates o
- Introduction
- lor to make these lines. It also optimally places points for laser projectors. And it does all of this wit