Fulltext results:
- Lasershow Converter Blender @tools:lcblender
- e created with perfect placement. * **Minimum Points in Laser frames** - This sets the minimum number of laser points rendered in each frame. * **Open Preview Wind... tion such as the Z-axis coordinates and number of points in the frame. ==== Blender Output and Laser Outp... ion, such as Z-axis coordinates and the number of points, at the bottom of this window * **Save Render
- Lasershow Converter Blender tutorial videos @tools:lcblender
- * Demo scenes - Grease Pencil * Demo scenes - Points Line types and filters * Demo scenes - Render S
- Utility: Object Point Spacing @tools:lcmax
- d, when running at a point output speed of 30,000 points per second. If you do not change any of the numbe... LC MAX. ===== About point spacing ===== The way points are placed in lines depends on whether the object... square, lines will always start with **AutoBlank Points at line endings**, followed by **AutoAnchor Points**. * If the object is round, a special point placeme
- What's new @tools:lcmax
- s. The additional information shows the number of points in the frame, as well as the Z-axis coordinates o... max:ultra-smooth_refresh-based_rendering#optional_points_in_other_tracks_parameter|Points in other tracks]] to the Ultrasmooth Refresh-based Animation rendering c
- Tips: Creating dust-like animations using particle systems @tools:lcmax
- ners. - 1.5 creates more particles but also more points - 2.0 reduces the amount of visible particles and the amount of points {{:tools:lcmax:dust-1.png|}} 4. Adjust the **O
- Tips: Using renderable splines @tools:lcmax
- splines which generally result in a lot of laser points being used. If you only have a few splines in the
- Tips: Point spacing for objects @tools:lcmax
- default point spacing settings have the **Corner points 165-170°** value set to zero. But this might make... positions. Therefore, it is best to set **Corner points 165-170**° to the same number as sharper (larger)... a round outline. One way is to set the **Corner points** at various angles to a value of 0. {{:tools:lc... urve Detect ===== Once you have prevented corner points from being placed on the sphere outline (either b
- Tips: Point spacing for lines @tools:lcmax
- results in laser frames with the least number of points. {{:tools:lcmax:point-spacing-for-lines-1.png?no... t value of 300. This ensures there will be enough points placed for small details and to avoid rounding in... <sup>[[#fn__1|1)]]</sup> setting for **AutoAnchor Points** (shown below) has **Accelerate/Decelerate** ena... n and out of lines. It also reduces the number of points that you need to use at the beginning and ending
- Utility: Object Line Types @tools:lcmax
- the object, but does not actually write any data (points) to the laser frame. This lets the object mask or... eeing other objects) and keep them from producing points. ===== See Also ===== * [[tools:lcmax:contour
- Utility: Object Quick-Setup @tools:lcmax
- d. Thus, you might need to adjust the "AutoAnchor points at corners" settings, so that a corner is seen.
- Tips: Scan speeds and LC4D @tools:lc4d
- when the ILDA Test Pattern is displayed at 30,000 points per second: | {{:tools:lc4d:sslc4d1.jpeg?nolink|... Now, some people may adopt a scan speed of 30,000 points per second. In fact, this is Pangolin's suggestio... ere are two cases: You tune and project at 30,000 points per second, or you prefer other speeds for tuning... n Lasershow Converter MAX. This is usually 30,000 points per second. Lasershow Converter MAX's default se
- Tips: Scan speeds and LC MAX @tools:lcmax
- when the ILDA Test Pattern is displayed at 30,000 points per second: | {{:tools:lcmax:scan-speed-lcmax-1.... Now, some people may adopt a scan speed of 30,000 points per second. In fact, this is Pangolin's suggestio... n Lasershow Converter MAX. This is usually 30,000 points per second. Lasershow Converter MAX's default<su
- Utility: Object Filter Settings @tools:lcmax
- .0, Lasershow Converter MAX will not generate any points on the laser display if a line is less than 3.0 p
- Tips: Scan speeds and Lasershow Converter FLASH @tools:lcflash
- when the ILDA Test Pattern is displayed at 30,000 points per second: | {{:tools:lcflash:scanspeed1.jpg?no... Now, some people may adopt a scan speed of 30,000 points per second. In fact, this is Pangolin's suggestio... ere are two cases: You tune and project at 30,000 points per second, or you prefer other speeds for tuning... scanners, AND that images be projected at 30,000 points per second. Lasershow Converter FLASH's [[tools:
- Tips: Color and path consistency @tools:lcmax
- ut it could be that a better beam path with fewer points could be derived if you had set a different selec... jump around unnecessarily, or that extra blanking points were included during the drawing of the intersect