Fulltext results:
- PASS @safety
- projector including laser, scanners, shutter and power supply. You must also use a light sensor to ensu... projector-health-related properties: * Scanner power supply and internal PASS power supplies * Scanner position signals to derive: * Scanning velocity ... “Protected Area”) * PASS logic system * Beam Power during both blanked and non-blanked periods * C
- Beam Analyzer (LBA-C-100) @accessories
- beam analyzer designed to handle high continuous power while measuring beam parameters like the divergen... 100% 60% ^ 40% >| ^ Parameter ^ Range ^ | Optical power (*) (* *) | 0.1W - 100W | | Accuracy on power measurement (Calibrated on 635nm / 520nm / 445nm). Other ... e case with a fan when using the device with high-power beams for a long period. (* *) A correct alignme
- SafetyScan Lens and Kvant lens mount @safety
- beam is typically so small that the entire beam's power can enter a show-viewer's eye. Where safety regul... hown that the maximum amount of un-diverged laser power you can use while complying with the MPE is only ... around 10 milliwatts. Obviously, such a low laser power would not make a very effective show. Outside of ... enforced as vigorously, often times higher laser power is used. Nevertheless, aside from safety concerns
- FB4 SE Manual @hardware:fb4
- FB4 stores settings and what will happen after a power failure or power cycle. When starting up the FB4 the first time, the default **[Operation Mode]** is **... he new default and will stay active, even after a power cycle. Settings are stored / saved on the SD car... content at specific predefined times or when the power of the laser is turned on. Autoplay requires that
- Vectors and Points @beyond
- more. If the Sample rate is lower, then the laser power per Sample is higher, and overall the Output look... The total tracing path is longer and so the laser power has to cover a bigger(longer) space, which in tur... When the line has its full width, then the laser power spreads by the whole line width. When the line width is decreased by 50%, and the laser power stays the same, the line will look brighter becau
- QuickTarget Beam Settings @beyond
- ault, BEYOND uses static beams with a specialized power control system. The alternative model to this, is... you use frames, BEYOND cannot use the specialized power control system.** {{:beyond:targetedbeamsettings1-5.png?nolink|}} You can change the relative power of the QuickTarget Beam from 10 to 100 and also r... portant to note, each beam starts out at only 10% power. If you want higher power in that particular beam
- Using Effects in BEYOND @beyond
- ngle dots, ===== Color Effect, Brightness Effect, Power Effect ===== BEYOND has a group of 3 effects con... ing the level of specific dolor channels, and the Power Effect injects additional Anchor points to increase the power (brightness) in laser content. The Power effect can inject up to 10 anchor points into each point where
- Projector Settings Menus @beyond
- t parameter. It may have effects for laser output power; it is important for CPU/USB/Network loads which ... output. Additionally there is a problem of “over power” for vector frames. **Wide Angle Compensation**:... 500 or 700. ===== Minimum point number and Laser Power ===== Now that we understand why low point count... lasers in your system. Lasers that are linear in power will not be linear in apparent brightness, so we
- Networking for Lasershows, QuickShow, and Entertainment @quickshow
- degrade performance when run next to high voltage power, or other noise inducing electronics. * Con... e on Toms Guide]] If using a laptop, disable all power saving options. There are a lot of them, go through as many places as you can to disable all power savings options, sometimes they exist in the bios... soft.com/en-us/windows/forum/all/how-do-i-disable-power-save-mode-for-win10/557613ec-cda3-4867-823c-1b552
- QuickTargets Beam Settings @quickshow
- t also activate each beam and adjust the relative power individually** As another safety measure, each b... w. In addition, each beam starts out at only 10% power. If you want higher power in that particular beam position, you will need to increase the **Relative Power** setting for that beam. ---- See Also * [[q
- QuickTargets Beam Settings @beyond
- t also activate each beam and adjust the relative power individually** As another safety measure, each b... w. In addition, each beam starts out at only 10% power. If you want higher power in that particular beam position, you will need to increase the Relative Power setting for that beam.
- Networking for Lasershows, BEYOND, and Entertainment @beyond
- degrade performance when run next to high voltage power, or other noise inducing electronics. * Con... e on Toms Guide]] If using a laptop, disable all power saving options. There are a lot of them, go through as many places as you can to disable all power savings options, sometimes they exist in the bios... soft.com/en-us/windows/forum/all/how-do-i-disable-power-save-mode-for-win10/557613ec-cda3-4867-823c-1b552
- Advanced Color Settings @beyond
- ical problem for the white color is the different power of the projectors' laser modules, and our nonline... e can’t change our eyes, but can change the laser power balance and thus the color mix. **Non-linear Cor... . For beam shows – we mostly need to get the most power from our projector. That is why BEYOND offers 3 s
- Projector Settings @quickshow
- relative to human eye sensitivity instead of just power levels. However, systems with not well tuned driv... color for your liking, you can lower the maximum power output on each channel to do a basic color calibr... point number. QuickShow has a specially designed, power optimized system for beam generation used for Tar
- Timeline Event Tab @beyond
- ose. For beam shows, it make sense to use maximum power for all colors, for graphic shows is important ge... ation color balance. * This event uses the High Power color balance. ===== PangoScript ===== Each