Fulltext results:
- Vectors and Points @beyond
- more. If the Sample rate is lower, then the laser power per Sample is higher, and overall the Output look... The total tracing path is longer and so the laser power has to cover a bigger(longer) space, which in tur... When the line has its full width, then the laser power spreads by the whole line width. When the line width is decreased by 50%, and the laser power stays the same, the line will look brighter becau
- FB4 SE Manual @hardware:fb4
- FB4 stores settings and what will happen after a power failure or power cycle. When starting up the FB4 the first time, the default **[Operation Mode]** is **... he new default and will stay active, even after a power cycle. Settings are stored / saved on the SD car... content at specific predefined times or when the power of the laser is turned on. Autoplay requires that
- QuickTarget Beam Settings @beyond
- ault, BEYOND uses static beams with a specialized power control system. The alternative model to this, is... you use frames, BEYOND cannot use the specialized power control system.** {{:beyond:targetedbeamsettings1-5.png?nolink|}} You can change the relative power of the QuickTarget Beam from 10 to 100 and also r... portant to note, each beam starts out at only 10% power. If you want higher power in that particular beam
- Using Effects in BEYOND @beyond
- position. ===== Color Effect, Brightness Effect, Power Effect ===== BEYOND has a group of 3 effects con... ing the level of specific dolor channels, and the Power Effect injects additional Anchor points to increase the power (brightness) in laser content. The Power effect can inject up to 10 anchor points into each point where
- QuickTargets Beam Settings @quickshow
- t also activate each beam and adjust the relative power individually** As another safety measure, each b... w. In addition, each beam starts out at only 10% power. If you want higher power in that particular beam position, you will need to increase the **Relative Power** setting for that beam. ---- See Also * [[q
- QuickTargets Beam Settings @beyond
- t also activate each beam and adjust the relative power individually** As another safety measure, each b... w. In addition, each beam starts out at only 10% power. If you want higher power in that particular beam position, you will need to increase the Relative Power setting for that beam.
- Projector Settings Menus @beyond
- t parameter. It may have effects for laser output power; it is important for CPU/USB/Network loads which ... output. Additionally there is a problem of “over power” for vector frames. ===== Overall system load =... 500 or 700. ===== Minimum point number and Laser Power ===== Now that we understand why low point count... um point number. BEYOND has a specially designed, power optimized system for beam generation used for Tar
- Advanced Color Settings @beyond
- ical problem for the white color is the different power of the projectors' laser modules, and our nonline... e can’t change our eyes, but can change the laser power balance and thus the color mix. **Non-linear Cor... . For beam shows – we mostly need to get the most power from our projector. That is why BEYOND offers 3 s
- Quick Setup @quickshow
- ulated lasers. Generally less expensive and lower power laser projectors have TTL lasers, while more expensive and higher-power projectors use Analog-modulated lasers. You shoul
- Projection Zones @quickshow
- g to scan high duty-cycle images that might cause power limiting. Setting the **Minimum number of points*... ll because such blanking would tend to reduce the power of the display. When the **Prevent minimum number
- Projection Zones in BEYOND @beyond
- om trying to scan high duty-cycle which may cause power limiting. Setting the **Minimum number of points*... ll because such blanking would tend to reduce the power of the display. When the **Prevent minimum number
- The Configuration Dialog Box @beyond
- he maximum, or reflect and go back. **Reflection power (%)** - During reflection, motion speed can be decreased, and reflection power can control this decrease of speed. **Preserve b
- Test Patterns in BEYOND @beyond
- to display across. We’ve also included a laser power level slider to the right of this menu, that will allow you to adjust the power level of the test pattern being displayed. This i
- Projection Zones @beyond
- g to scan high duty-cycle images that might cause power limiting. Setting the Minimum number of points to... ll because such blanking would tend to reduce the power of the display. When the Prevent minimum number o
- Kinetic Lights Plugin @beyond
- ams, where we can set our destination (zone), its power, and if it Is enabled. These features work the sa... u use custom image, then BEYOND will stop dynamic power distribution and each beam will take as much poin
