Fulltext results:
- BEYOND DMX Settings
- rter. Currently BEYOND supports the __DMX USB PRO controller from the company ENTTEC__. This is a very popular... ct FB3-SE control and playback from a DMX console controller or application.// {{:beyond:dmxsettings1.png?no... means of ArtNet protocol, the Enttec DMX PRO USB controller or Pangolin QM2000 hardware. To setup the communi... urce. **Details for communication with the Enttec controller are located on other tab called ENTTEC**. To use
- BEYOND MIDI settings
- it by moving a slider or pressing a button on the controller. If it is connected correctly, you should see a M... ws/dialogs, work for FX too. To configure a MIDI controller to be able to activate the main cue grid of a BEY... , and for the secondary grid, you can use a MIDI controller like the Livid OHM.** Double click on a cell to ... }} Pay attention that as a rule, buttons on MIDI controller first send MIDI message when you press the button
- FB4 Settings Basics
- one important detail: The FB4 hardware may be the controller even if it is in another mode, or connected to an... a software, but it is not the only purpose of the controller. It is one of reasons why the FB4's are separate ... ode - enables the external ILDA signal input. The controller must be equipped with the optional hardware conne... provides control VIA the 5 PIN XLR DMX input; The controller must be equipped with the optional DMX hardware c
- Vectors and Points
- mes. The software sends the Frame to the hardware controller to transform the digital Frame to an analog waveform. The output from the controller is an analog signal. The same situation as in the... of speakers. In laser display – we have Frames, a controller for making the analog signal, a scanner amp, and ... as equal duration, but a different value. A laser controller uses the Samples as the input of the DAC (Digital
- Firmware Updater
- e version when it opens or an additional hardware controller is connected to the system (while BEYOND is open)... BEYOND detects incorrect firmware is loaded on a controller, BEYOND will update it. Otherwise, the controller cannot be used within BEYOND. During a firmware update, BE... ts of desktops. **Problem with computer USB Host controller** - Very unexpected issue, but sometimes the con
- BEYOND Laser and EmuLaser control hardware
- rop down list) displays a list of connected laser controller hardware units, virtual controllers (demo), and E... installed and working correctly with that QM2000 controller. LD2000 must be installed and working with your QM2000 before BEYOND can access and use the controller. Demo projectors are available to use BEYOND in demo mode. For adding a demo controller, click on the “Add” button on the toolbar. The
- TimeCode and BEYOND
- ick on the Main “Settings” menu and select ”SMPTE Controller Settings”. - Click on “Enable controller communication” to create a corresponding communication component ... lect a communication port that corresponds to the controller you are using. - Select the time format and en... t button to start communication with the TimeCode controller which will perform a test connection. At the end
- Using a Gamepad in BEYOND
- ed settings within the Control Panel. The Gamepad controller may require calibration and it is important to se... BEYOND, the settings are very simple. Select the controller inside the Controller list, BEYOND will show information about the controller, and allow testing of the device. ===== Gamepad and
- BEYOND and the X-Box Kinect 360
- Software is compatible with the X-Box Kinect 360 Controller, and this combination allows you to create a wide... nsure that it is functioning properly. The Kinect controller can be used together with the Kinect SDK and tool... is a setting specifically designed for the Kinect controller. - Universe. This is mostly for fun. With the
- BEYOND Security Guide
- ized Users You need to know the serial number of controller that will be used by the authorized user, or deci... uld confirm that you are the Author/creator. Your controller must be connected or password registered in the s
- Art-net DMX and sACN
- t FB3-SE control and playback from a DMX console, controller or application.//** There are many ways you may ... make a console control BEYOND almost like a midi controller, allowing for all zone and cue setup within BEYON
- Advanced Color Settings
- ype and ##### is the 5-digit serial number of the controller. BEYOND loads the Projector Settings File as soon as the controller is connected to the software.
- FB4 Browser
- ders contained on the FB4 SD card, of the current controller. Standard files have predefined icons. Other file... **Reboot FB** – restart/reboot the current FB4 controller. ===== Status Panel ===== The Status Panel ind
- DMX Settings
- r that, specify the COM port where the DMX-to-USB controller is connected. BEYOND gives you the ability to te... to send up to 512 channels. {{:beyond:dmx_3.png|controller}} The DMX Output settings also has advanced cont
- Projection Zones in BEYOND
- a listing is red, it is because there is no laser controller that is able to output to that projector (scanner... to**” allows you to indicate the projector (Laser Controller Serial number) that will be used for that zone, a