Fulltext results:
- Utility: Object Point Spacing
- ====== Utility: Object Point Spacing ====== This panel allows you to control the point placement on an object-by-object basis. Although ... st scenes, it is still very useful to specify the point placement settings on an object-by-object basis. {{:tools:lcmax:object-point-spacing.png?nolink|}} **Note**: The numbers show
- Tips: Point spacing for objects
- ====== Tips: Point spacing for objects ====== Although Lasershow Converter MAX's default((For any number... ults for most scenes, it is still handy to assign point placement settings on an object-by-object basis. ... ts ===== In the New York scene below, the arrows point to lines on the buildings that have a fairly shallow angle. {{:tools:lcmax:point-spacing-for-objects-1.gif?nolink|}} The default
- Tips: Point spacing for lines
- ====== Tips: Point spacing for lines ====== ===== Variable vs. constant point density ===== The default((For any number value,... AutoSpace Distance** (shown below) place a higher point density in areas of the image that have curved lines, and a lower point density in areas of an image that have straight l
- Utility: Object Quick-Setup
- ttings|filter settings]] and [[tools:lcmax:object_point_spacing|point spacing]] are changed to settings which are typical for that object. (Of course, you can m... ers**. Sets filter to minimum (but not off). Sets point spacing for fairly sparse visible density, with a... the sphere becomes very small. In this case, the point density might need to be adjusted. Adjustment ma
- Tips: Color and path consistency
- === As was discussed in the [[tools:lcmax:object_point_spacing|Object Point Spacing]] topic, it is highly desirable for the beam path to stay consistent from o... thin an object, by using the [[tools:lcmax:object_point_spacing|Object point spacing]] panel **Beam path for this object** drop-down list. Note that whatever o
- Utility: Overview
- bject Filter Settings]] * [[tools:lcmax:object_point_spacing|Object Point Spacing]] * [[tools:lcmax:object_soft_line|Object Soft Line]] * [[tools:lcmax... or and path consistency]] * [[tools:lcmax:tips_point_spacing_for_lines|Tips: Point spacing for lines]] * [[tools:lcmax:tips_point_spacing_for_objects|Tips
- LC Max
- bject Filter Settings]] * [[tools:lcmax:Object Point Spacing|Object Point Spacing]] * [[tools:lcmax:Object Soft Line|Object Soft Line]] * [[tools:lcmax:... ra lines on cone object]]s * [[tools:lcmax:Tips Point spacing for lines|Tips: Point spacing for lines]] * [[tools:lcmax:Tips Point spacing for objects|Tips
- What's new
- in, we have removed support for LD2000. From this point forward, LC-Max will only work with BEYOND. ====... with 3ds Max version 9.0 and later, the floating point calculations are more accurate. As a result, inte... -setup panel]]. * Enhanced [[tools:lcmax:object_point_spacing|Object point spacing panel]]. * [[tools:lcmax:questions_and_answers|Improved rendering speed]]
- Renderer: Laser Output
- ximum of 30 frames per second if the sample rate (point output speed) was set to 30,000 points per second... re put in a blanked line that leads from the last point back to the first point in the frame. ===== Handling of "Frame 0" in 3ds Max ===== You might notice t
- Tips: Creating dust-like animations using particle systems
- .5 and 2 -- with 1.8 being a pretty good starting point, but this depends on your laser scanners. - 1.5 ... tools:lcmax:dust-1.png|}} 4. Adjust the **Object point spacing** settings in the utility plugin. Since y
- Utility: About object settings
- Object Filter Settings]] and [[tools:lcmax:object_point_spacing|Object Point Spacing]] panels. ---- [[tools:lcmax:|Go Back]]
- Tips: Scan speeds and LC MAX
- ooking in the picture on the [[tools:lcmax:object_point_spacing|Object Point Spacing]] topic page. ===== Better scanners give better results ===== Lasershow C
- Tips: Beam path optimization
- this object** (found in the [[tools:lcmax:object_point_spacing|Object point spacing]] panel) controls how the beam travels. ===== Controlling the beam path wi
- Tips: Importing artwork
- l -- you will be able to assign colors, and laser point placement settings differently for each object if
- Tips: Using MAX-defined
- x:using-max-defined-8.gif?nolink|}} | 7. At this point, you can select the edges of the object that you